TARCO Highlander Junior HL-JR - Ice & Snow Control Spreader

SPECIFICATIONS

MODEL	HL-JR-7 HL-EL-JR-7	HL-JR-8 HL-EL-JR-8	HL-JR-9 HL-EL-JR-9	HL-JR-10 HL-EL-JR-10	SP-8	SP-9
Hopper Length	80"	92"	108"	120"	96"	108"
Hopper Height	35"	35"	35"	35"	42"	42"
Hoper Width	48"	48"	48"	48"	72"	72"
Overall Length	104"	116"	132"	148"	120"	132"
Capacity (cubic yards levels)	1.5	1.86	2.25	2.5	3.0	3.3
Capacity w/Opt. 6" Hopper Ext	2.0	2.46	2.92	3.25	3.89	4.3
Weight w/Screens (opt) & GECEL	880 lb.	940 lb.	1,050 lb.	1,110 lb.	1,360 lb	1,450 lb
Hopper Const.	14 GA	14 GA	14 GA	14 GA	12 GA	12 GA
Number of Hopper Side Supports (per side)	3	3	4	4	3	3
Chevron Conveyor Chain 15" Wide	Std.	Std.	Std.	Std.	Std.	Std
Conveyor Bridge	Opt.	Opt.	Opt.	Opt.	Std.	Std.
Top Screen(s) Opt	1 Flat	1 Flat	2 Flat	2 Flat	2 Hinged	2 Hinged
Single Center Lift Point	Std.	Std.	N/A	N/A	N/A	N/A

POWER UNITS:

GECEL:  Briggs & Stratton  10.5 horsepower I/C air-cooled engine with an electric clutch.  The engine has an electric throttle, electric start, choke and stop controls for cab installation.  The engine and battery are enclosed by a vented steel enclosure.  A manual pull start is supplied in case of battery failure.

HY:  A single hydraulic motor is coupled to the 20:1 gearbox to drive the conveyor chain and spinner motor.  Hydraulic hoses and quick couplers are supplied to reach the rear of the truck.  Vehicle must be equipped with a hydraulic system capable of producing 8 GPM at 1500 PSI.

HY2: Dual hydraulic motor drive to allow independent spinner and conveyor speed.  One hydraulic motor is couple to the gearbox to drive the conveyor chain and another hydraulic motor is couple to the spinner disc.  Hydraulic hoses and quick couplers are supplied to reach the rear of the truck.  Vehicle must be equipped with a hydraulic system capable of producing 12GPM at 1500 PSI.

HOPPER:  The hopper body is full welded steel (optional type 304 stainless steel).  The hopper sides and conveyor are formed with one sheet of steel to eliminate rust seams.  Hopper side supports rest on 2" channel crossmembers to help support the sides.  The hopper top edge is channel formed for strength and sides are sloped at 45 degree to insure free flow of material.  A fully adjustable rear flow gate, four corner lift loops and a single center lift point (HL-JR-7 & HL-JR-8 models only).  Steel units are properly cleaned and primed then a finished yellow enamel paint is electrostatically applied.  Stainless steel units are left unpainted natural stainless.

CHEVRON CONVEYOR:  The Chevron Conveyor System incorporates a plurality of diagonal conveying elements that results in a constant feed of material to the spinner disc regardless of the conveyor speed.  The conveyor system is 15" wide to eliminate material bridging.  The conveyor chain has an adjustable spring-loaded idler roller with over 3" of travel.  A 10 gauge steel replaceable conveyor wearplate supports the underside of the conveyor.  A 20:1 right angle gearbox drives the conveyor and the conveyor chain.  The drive sprockets are cast iron with 8 teeth, keyed and set screwed to the 1-1/4" diameter gearbox drive shaft.  Both the conveyor drive shaft and idler shaft are supported by greaseable flange bearings.