TARCO Highlander Saratoga - Ice & Snow Control Spreader

TARCO Highlander Saratoga - Ice & Snow Control Spreader

The HIGHLANDER® SPREADER uses a unique hydraulic motor to drive the conveyor chain, the Saratoga Power-Pak. The Saratoga Power-Pak is a piston hydraulic motor. When used on a hopper body spreader it provides distinct advantages over conventional 50:1 gear reduction drive.

Compare the "performance features" of the Saratoga Power-Pak to a conventional gear reduction hydraulic drive.
Conveyor Drive System Comparison	Drive Shaft Speed	Hydraulic Oil Pressure	Starting Torque
Conventional 50:1 Gear Reduction - Hydraulic Drive	6-22 RPM	1000-1500 PSI	13,000 IN/LBS (1100 FT/LBS)
Saratoga Power-Pak - Hydraulic Powered	1/2-40 RPM	300-600 PSI	21,000 IN/LBS (1750 FT/LBS

HOPPER SIZE

HOPPER LENGTH	LEVEL CAPACITY (yd3)	WIDTH	HEIGHT	LENGTH O.A. (approx.)	LEVEL CAPACITY WITH HOPPER EXTENSIONS
HOPPER LENGTH	LEVEL CAPACITY (yd3)	WIDTH	HEIGHT	LENGTH O.A. (approx.)	2"	4"	6"	8"	10"	12"
8'	5.0	80"	52"	10'	5.2	5.5	5.9	6.2	6.5	6.9
9'	5.5	80"	52"	11'	5.9	6.2	6.6	7.0	7.4	7.7
10'	6.1	80"	52"	12'	6.5	6.9	7.3	7.7	8.2	8.5
11'	6.8	80"	52"	13'	7.3	7.7	8.0	8.6	9.1	9.4
12'	7.3	80"	52"	14'	7.9	8.4	8.7	9.4	9.9	10.2
13'	8.0	80"	52"	15'	8.5	9.1	9.6	10.1	10.7	11.2
14'	8.7	80"	52"	16'	9.3	9.9	10.4	11.0	11.6	12.2
15'	9.3	80"	52"	17'	9.9	10.5	11.2	11.8	12.4	13.0
16'	10.0	80"	52"	18'	10.5	11.2	11.9	12.5	13.2	13.9

Other sizes and dimensions are available upon request.
NOTE: To figure the load any model will carry, use these approximate material weights: 1 cu. yd. dry salt - 2200 lbs.; 1 cu. yd. wet sand - 3300 lbs.

HOPPER LENGTH: 8 FT. - 16 FT.

CAPACITY: 5.0 - 14 cubic yard

HEIGHT: 52" WIDTH: 80"

HOPPER BODY CONSTRUCTION: Full welded construction of 10 gauge steel. (See options for special construction and materials.) Rack & pinion controlled discharge gate. Wear plate: 3/16" thick abrasion resistant steel. Spring loaded front idler assembly with roller, no sprockets required. Four (4) hopper lift loops. Entire unit is painted with a metal primer and a finish coat of yellow enamel.

CONVEYOR: Bar flight design 24" wide. Flight dimensions 3/8" x 1-1/2" cross section. Pintle side link chain with 2.25" pitch with 21,000# tensile strength per strand. Drive sprockets are 8 tooth cast iron keyed to 2" diameter drive shaft.

SPINNER ASSEMBLY: Spinner disc is 20" in diameter with 6 bolt-on vanes (optional urethane disc). Direct coupled hydraulic motor installed under disc. Entire spinner assembly tips-up for storage and stockpiling.

CONVEYOR DRIVES AVAILABLE:
MODEL HL-HY2P: The Saratoga Power-Pak is a piston hydraulic motor delivering 1/2 to 40 RPM on the conveyor shaft.

MODEL HL-G-HY2P: Saratoga Power-Pak, powered by a self contained hydraulic system equipped with an 18 H.P. gasoline engine, hydraulic pump and oil reservoir.

PARTIAL LIST OF OPTIONAL ITEMS: •Stainless steel construction •Corten steel construction •7 gauge steel construction •Top screens •Lighting packages •Spinner spot light (s) •Hold down equipment •Conveyor bridge •Catwalks •Hopper extensions •Cab shield •Rubber spill aprons •Chevron conveyor system** •Belt-over-chain conveyor •Special conveyor chains •Hoist-It-Legs*** •Top mounted spinner motor (s) •Urethane spinner disc (s) •Spreader controls •Special paint & epoxy

*Saratoga Power-Pak-U. S. Patent #4,023,689 and Patent #4,108,010
**Chevron Chain System-U. S. Patent #4,043,446. Canadian Patent #1,032,489
***Hoist-It-Legs-U. S. Patent #3,623,621

Sales Price: $0.00

Qty: